Craftsman 2.5 hp radial arm saw manual

I need my shop space back. As you can see in the attached pictures — the saw is i Great shape, lowered to This Craftsman Professional 2.

For angle cuts, the turret arm allows the saw to travel over the ce Sears Craftsman 10" Radial arm saw. Model number This was completely setup, cleaned and tweaked for a project early lastspring BUT am retiring and downsizing so this has t. Accessories included:sanding drummolding toolextra bladesdado attachmentvacuum attachment Cash only.

Must pick up and haul yourself. This is a table saw , clearly used and dusty, but in working condition from what I understand. What is shown here is exactly what you'll get. Feel free to contact me for questions or concerns. Cross cut or Head adjustable for depth, ripping, and angle.

Older model but works as it should. Please reference item in your communications. Works great, good condition. Used very lightly in recent years. Located on east side of Des Moines. Please call for more information. Equipped With:Mit. Page 29 Recheck the rotation by holding the front of the arm, grasping the top of the column support with the other, and pressing the arm to the side. Page 30 Loose carriage bearings permit the blade to wander slightly while cutting, which will result in a poor cut and more wear and tear on the saw.

Use the following steps to check for tightness and to then adjust the bearings if needed. Page 31 Move the arm to the opposite side and repeat the above procedure. When the opposite side is level, recheck the first side to make sure that it is still accurate and even. Line up the hole in the U-clip with the saw base hole just to the left of the center notch in saw base.

See Figure 23B. Page 34 See Figures 26A and 26B. Place the inner blade washer, saw blade, outer blade washer, and blade nut on the blade arbor. See Figure 26A, Note: The conca've side of blade washers go against the blade. When ripping the riving knife must be centered with the blade to ride in the middle of the kerr and keep it from binding.

Binding pinches the blade. Blade pinching can cause kickback. There are two pairs of anti-kickback pawls. Page 36 The control cut device offers many benefits. As it increases operator control, it eliminates the risk in a cross cut of the saw "climbing" out and over the workpiece at the operator. Feed control of the blade as it cuts through the workpiece increases, as does the accuracy of the cut.

Page 37 0" and leave it unlocked. Lock the yoke lock handle right side of saw, below yoke and the bevel lock lever. Page 38 Place the square flat against the blade between two teeth. Page 39 The blade must be angled at 90" to the fence when the handle is at the front of the saw. If not, kickback could result during a cross cut. Kickback can cause serious injury by throw- ing the workpiece toward the operator.

In addi If you can see a gap, adjust the blade to be at 90" bevel to the table with the following steps. The rip scale indicators on the arm show the distance between the blade and the rip fence. The upper scale is used when the fence is positioned directly behind the front table. The lower scale is used when the fence is at the extreme rear, directly in front of the column. Page Labels The control cut device offers many benefits.

It can make dado or molding cuts with special attachments. This saw is designed to cut wood and wood composi- tion products only. Page 44 The yellow switch key prevents accidental starting of the main power switch when saw is not being used.

To activate the switch, insert the switch key and lift switch to ON position. To lock the switch once it has been pressed to OFF, remove the yellow key. Refer to the drawings and instructions provided so you can make safer and more precise cuts. Turn the saw off with the switch on the arm but hold the handle until the blade stops rotating. Adjust the height with the elevating handwheel so the blade will rotate freely in the kerr. Adjust the height with the elevating handwheel so the blade will rotate freely in the kerf.

Adjust the height with the elevating handwheel so the blade will rotate freely in the kert. Adjust the height with the elevating handwheel so the blade will rotate freely in the keff. I will consider motor freight if someone wants it that badly. I will work out the details on-demand, but I think there are companies that will accept, and crate, drop-offs or do residential pickup.

Contact Seller. Contact Information: Please provide your contact information below. All fields are required. Report This Ad. Use this form to report the selected post to the site administrators. Reporting should generally be used only if the post breaks site rules. Our purpose is to provide information about vintage machinery that is generally difficult to locate.

Catalogs, manuals and any other literature that is available on this site is made available for a historical record only. Please remember that safety standards have changed over the years and information in old manuals as well as the old machines themselves may not meet modern standards. It is up to the individual user to use good judgment and to safely operate old machinery.

The VintageMachinery. About Us. Discussion Forum.